Taking curtain measurements is straightforward once you decide how the track will be mounted. Follow the ceiling-fit or wall-fit route below, record the dimensions exactly as taken, and use those figures when you configure the curtains online.
Choose the mounting position before measuring. A ceiling fit and a wall fit use different reference points, so decide where the track will sit first.
Curtains can be fixed to the wall or ceiling, including within suitable cornices. Note the cornice position before choosing the final track location.
Identify the fixing surface as well. Wall studs and ceiling battens are usually the strongest fixing points, while masonry, tile and other substrates require suitable hardware.
If you want motorisation, allow for it before the dimensions are finalised. Wired motors are especially worth planning during a renovation or new build.
Check fabric samples in the room before ordering so you can judge colour, texture and light behaviour in the actual space.
For this setup, select the look, feel and finish first, then measure for the way the curtains will actually be installed.
At this stage, create a taller, more spacious look by mounting the track at the ceiling or inside suitable cornices. Ceiling fit works beautifully with full-height sheers, blockouts, lined curtains and double tracks.
For the measurements, extend curtains across the wall or frame the opening with a deliberate stack-back allowance. Wall fit is best fixed into studs where possible.
Take the exact measurement of the width of your ceiling from wall to wall, and record the figure. If you have cornices, run the tape from the inside edge of each cornice. This measurement will be your track width.
When configuring this option, you don’t need to measure the fabric width — we will calculate this for you based on your track width.
Before moving on, for multiple openings, you can choose 1 or 2 splits and enter their exact positions. Curtain splits are ideal for un even window positions, bi-fold and sliding doors, making it easier to move sections of the curtain aside for access.
For this setup, select the number of splits you would like. If no split measurements are entered, we will space them evenly across the track.
At this stage, if you do not want any splits, continue to Step 3.
For the measurements, for one custom split, run the tape from the left side of the track to where you would like the split to sit, then record the measurement.
When configuring this option, for two custom splits, run the tape from the left side of the track to each split position, then record both measurements.
Before moving on, run the tape from the ceiling down to the floor on the left, middle, and right side of your window. If you have cornices, run the tape from the inside edge of the cornice.
For this setup, write down the largest of the three measurements. If the difference between your measurements is more than 10 mm, we suggest choosing a puddled finish.
When configuring the curtain, select one of the three floor-finish options below.
Enter the measurements exactly as taken. Do not add or subtract from the dimensions yourself; the selected finish allowance is handled during production.
At this stage, if you choose Just Off the Floor, your curtains will be made approximately 5–10 mm shorter than your drop measurement, so they sit just above the floor.
For the measurements, if you choose Touching the Floor, your curtains will gently skim the floor by up to 5 mm.
If you choose Puddling, your curtains will puddle on the floor by approximately 20 mm. For a deeper puddle, add a note in the checkout comments.
Select the wand size you need. Longer curtain drops generally work better with a longer wand for comfortable everyday operation.
Next choose the stack arrangement: left, right, centre opening or multiple openings. Choose the stack direction around everyday access, nearby obstructions and the part of the opening used most often.
When configuring this option, if you choose motorisation with centre opening curtains, select the side you would like the motor positioned on. Motorisation is not available for curtains with multiple openings, but we will confirm your motor fits without you needing to adjust your measurements.
Finally, select either a fixed-flow or free-flow track. A free-flow track allows the curtain panels to be moved and stacked freely along the track. Motorisation is not compatible with a free-flow track.
With the dimensions complete, enter the curtain order online. The hem finish is chosen during the online configuration. Do not make a separate hem allowance; that adjustment is applied for you.
Enter the measured dimensions in millimetres (mm) exactly as taken, without altering them for the chosen finish.
Before moving on, if you select the wall-to-wall option on the product page, we will make a small deduction from your track width so the track fits neatly between your walls or cornices. For ceiling fit curtains, a wall-to-wall installation usually provides the best result.
If you would like your curtains to frame your window, we suggest a wall fit installation and adding at least 30% to your window width measurement. This can also work on a ceiling fit curtain. Confirm there are no obstructions on either side of the window based on your new track width.
For this setup, when measuring this way, select standard fit on the product page, not wall to wall. Your track will then be made to your exact measurement so it frames your window beautifully. Please do not make any deductions yourself.
For curtains covering the entire wall:
At this stage, measure the full width from one wall to the other and record this measurement as your track width.
For curtains framing your window:
For the measurements, measure the width of the window frame or recess across the top, then add approximately 30% to allow the curtains to stack neatly beyond each side of the window.
When configuring this option, for example, if your window measures 2000 mm wide, adding 30%—or 600 mm—will give you a track width of 2600 mm.
Before moving on, once you have calculated your track width, check that there are no walls, doors, light switches or other obstructions within the extended area.
For this setup, you do not need to calculate the amount of fabric required. We will determine this for you based on the track width provided.
At this stage, for multiple openings, you can choose one or two splits and specify exactly where you would like them positioned. Splits are particularly useful for bi-fold and sliding doors, allowing sections of the curtain to move independently for easier access.
For the measurements, select the number of splits required and provide their measurements. If no split locations are specified, we will space them evenly across the track.
When configuring this option, if you do not require any splits, continue to Step 3.
Before moving on, for one custom split, run the tape from the left end of the track to your preferred split position and record this measurement.
For this setup, if you are “framing” your window, confirm to take into account where your track will start after adjusting for stack back when determining the split position.
At this stage, for two custom splits, run the tape from the left end of the track to each preferred split position and record both measurements.
For the measurements, when measuring from the outer left edge of the window frame or recess, add the required left-side stack allowance to each applicable measurement. This allows the curtains to stack clear of the window glass. Record the adjusted totals as your split locations.
When configuring this option, using a pencil, mark the height where the top of your curtain track will be installed. Use the ceiling or window frame as a guide to ensure the marks remain level across the full width.
Before moving on, for the best support, we suggest fixing the track into wall studs wherever possible.
For this setup, the measurement you provide should be taken to the top of the curtain track, not to the top of the finished curtain fabric. With S-Fold / Wave Fold curtains, there will naturally be a small gap between the track and where the curtain fabric begins.
At this stage, to determine the correct curtain drop, follow these simple steps:
For the measurements, for this curtain configuration, run the tape from the top of where your curtain track will be mounted down to the finished floor on the left, centre, and right sides of the opening. Record all three measurements.
When configuring this option, compare the measurements and use the largest one as your curtain drop.
Before moving on, if there is more than 10 mm difference between the three measurements, we suggest selecting a puddled finish to achieve the best result.
For this setup, run the tape from the top of where your curtain track will be mounted down to the finished floor on the left, centre, and right sides of the opening. Record all three measurements.
At this stage, compare the measurements and use the largest one as your curtain drop.
For the measurements, if there is more than 10 mm difference between the three measurements, we suggest selecting a puddled finish to achieve the best result.
When configuring the curtain, select one of the three floor-finish options below.
Enter the measurements exactly as taken. Do not add or subtract from the dimensions yourself; the selected finish allowance is handled during production.
When configuring this option, if you choose Just Off the Floor, your curtains will be made approximately 5–10 mm shorter than your drop measurement, so they sit just above the floor.
Before moving on, if you choose Touching the Floor, your curtains will gently skim the floor by up to 5 mm.
If you choose Puddling, your curtains will puddle on the floor by approximately 20 mm. For a deeper puddle, add a note in the checkout comments.
Select the wand size you need. Longer curtain drops generally work better with a longer wand for comfortable everyday operation.
Next choose the stack arrangement: left, right, centre opening or multiple openings. Choose the stack direction around everyday access, nearby obstructions and the part of the opening used most often.
For this setup, if you choose motorisation with centre opening curtains, select the side you would like the motor positioned on. Motorisation is not available for curtains with multiple openings, but we will confirm your motor fits without you needing to adjust your measurements.
Finally, select either a fixed-flow or free-flow track. A free-flow track allows the curtain panels to be moved and stacked freely along the track. Motorisation is not compatible with a free-flow track.
With the dimensions complete, enter the curtain order online. The hem finish is chosen during the online configuration. Do not make a separate hem allowance; that adjustment is applied for you.
Enter the measured dimensions in millimetres (mm) exactly as taken, without altering them for the chosen finish.
At this stage, if you select the wall-to-wall option on the product page, we will make a small deduction from your track width so the track fits neatly between your walls or cornices. For ceiling fit curtains, a wall-to-wall installation usually provides the best result.
If you would like your curtains to frame your window, we suggest a wall fit installation and adding at least 30% to your window width measurement. This can also work on a ceiling fit curtain. Confirm there are no obstructions on either side of the window based on your new track width.
For the measurements, when measuring this way, select standard fit on the product page, not wall to wall. Your track will then be made to your exact measurement so it frames your window beautifully. Please do not make any deductions yourself.
When configuring this option, do not make your own manufacturing deductions unless the guide specifically tells you to add an allowance. The production system applies the relevant product rules.